110V Universal Hammer Mill Grinder Pulverizer Heavy Duty Grain Heavy Duty Machine. Universal pulverizer utilizes the high-speed relative motion between the moving and regular tooth set, which makes the material crushed through concussion, rub and crush. The structure of machine is simple and firm, the operation is steadily and the result of crushing is well. The materials are discharged directly from mainframe, the size of the granularity is gained through changing different pore size sieve. In addition, this machine is made of the stainless steel, surface of the inside of the machine is smooth, which changes the phenomenon of inboard wall coarse and accumulating of powder in the past. It is more in line with the national standard in the fields of pharmaceutical, chemical production and food. It is only suitable for. Wet materials or liquid might make the machine break down. Suitable for the too. The reasones of those cannot serve as return. It should be checked before using the machine that whether transmission parts are loose or the other anomaly is produced, the direction of the machine operation should be consistent with the direction of the arrow shown. Taking no-load test for 1-2 minutes before using the machine. Materials can be feed after the machine is operating normally. Increasing the feed gradually and taking observation of electric current and the functioning of the motor. Blanking flashboard can be fixed only after feeding and current balance to be in normal. Drying the materials or using coarse screen stencil if the materials are too wet or have poor mobility, which cause poor discharge. Opening the front cover to Replace the screen stencil. Hand wheel must be tightened to ensure the front cover and the case remain sealed. Stopping feed for 5-10minites before shutdown the machine in order to reduce the residual material. ×820mm(22″14″32). 10,20,30,40,50,60,80,100,120 mesh. The machine calculate the output by. Western medicine raw materials. Because the materials are different, It is difficult to achieve uniform standards. The output also depend on the. Size of the mesh. The smaller particle will cause the lower output. Different View Of Machine. The Upward View of Machine. The Gear of Machine. Regular checking bearing and replacing with high-speed butter to ensure the normal operation of the machine, it is necessary to frequently check wearing parts which need to be timely replaced if there is any severe wear phenomena. When operating the machine, if spindle speed was found to gradually decline (Triangle loosed) turn off the machine and downward adjustment of the motor (attention to the same elastic of the Triangle, if there is inconsistencies in the Triangle, replace it). This will enable the machine can achieve the required speed. Abnormal checks should be shutdown. Metal materials are strictly prohibited inflow the inside when the machine is running, such as nails, iron and so on. Cleaning of residues in various parts of machine after turning off it, the machine which is disabled for a long time require to be wiped out and is with good cover sheeting. 1 set of universal pulverizer SF130(150022). Orders are processed from Monday-Friday; Not on the weekends & public holidays. We will work with you to get the case resolved in the fastest method. Hope for your understanding. Please contact with us at first for more details. Defective & Damaged Products. If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it’s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. If an item is received damaged, customer service must be contacted within 7 days of receiving your item. Payments via eCheck do not clear immediately. Usually you will wait 5-7 days after checkout for it to clear. This item is in the category “Business & Industrial\Heavy Equipment, Parts & Attachments\Heavy Equipment\Mining Equipment”. The seller is “asctop40″ and is located in this country: CA. This item can be shipped to Canada, United States.

• MPN: 150022
• Equipment Type: Hammer Crusher
• Make: Universal

Universal pulverizer utilizes the high-speed relative motion between the moving and regular tooth set, which makes the material crushed through concussion, rub and crush. The structure of machine is simple and firm, the operation is steadily and the result of crushing is well. The materials are discharged directly from mainframe, the size of the granularity is gained through changing different pore size sieve. In addition, this machine is made of the stainless steel, surface of the inside of the machine is smooth, which changes the phenomenon of inboard wall coarse and accumulating of powder in the past. It is more in line with the national standard in the fields of pharmaceutical, chemical production and food. It is only suitable for. Wet materials or liquid might make the machine break down. Suitable for the too. The reasones of those cannot serve as return. It should be checked before using the machine that whether transmission parts are loose or the other anomaly is produced, the direction of the machine operation should be consistent with the direction of the arrow shown. Taking no-load test for 1-2 minutes before using the machine. Materials can be feed after the machine is operating normally. Increasing the feed gradually and taking observation of electric current and the functioning of the motor. Blanking flashboard can be fixed only after feeding and current balance to be in normal. Drying the materials or using coarse screen stencil if the materials are too wet or have poor mobility, which cause poor discharge. Opening the front cover to Replace the screen stencil. Hand wheel must be tightened to ensure the front cover and the case remain sealed. Stopping feed for 5-10minites before shutdown the machine in order to reduce the residual material. 820mm(22″14″32). 10,20,30,40,50,60,80,100,120 mesh. The machine calculate the output by. Western medicine raw materials. Because the materials are different, It is difficult to achieve uniform standards. The output also depend on the. Size of the mesh. The smaller particle will cause the lower output. Different View Of Machine. The Upward View of Machine. The Gear of Machine. Regular checking bearing and replacing with high-speed butter to ensure the normal operation of the machine, it is necessary to frequently check wearing parts which need to be timely replaced if there is any severe wear phenomena. When operating the machine, if spindle speed was found to gradually decline (Triangle loosed) turn off the machine and downward adjustment of the motor (attention to the same elastic of the Triangle, if there is inconsistencies in the Triangle, replace it). This will enable the machine can achieve the required speed. Abnormal checks should be shutdown. Metal materials are strictly prohibited inflow the inside when the machine is running, such as nails, iron and so on. Cleaning of residues in various parts of machine after turning off it, the machine which is disabled for a long time require to be wiped out and is with good cover sheeting. 1 set of universal pulverizer SF130(150022). Orders are processed from Monday-Friday; Not on the weekends & public holidays. We will work with you to get the case resolved in the fastest method. Hope for your understanding. Please contact with us at first for more details. Defective & Damaged Products. If product was received damaged or not as described, please send us some pictures or videos, so we could well understand your problem, then solve them for you ASAP. Besides, it’s much helpful for us to claim with UPS, remind our related department to pay much more attention to packaging later on. If an item is received damaged, customer service must be contacted within 7 days of receiving your item. Payments via eCheck do not clear immediately. Usually you will wait 5-7 days after checkout for it to clear. This item is in the category “Business & Industrial\Heavy Equipment, Parts & Attachments\Heavy Equipment\Mining Equipment”. The seller is “art_asc365″ and is located in this country: CA. This item can be shipped to Canada.

• MPN: 150022
• Equipment Type: grinder
• Brand: Unbranded/Generic